x
Teklif İsteyiniz
Paylaş:
Fiyat Alarmı

ATMEGA328P Microcontroller Development Board, Arduino-Compatible

Ürün Kodu : LTE-WS19287
Yorumlar
4.139,90 TL + KDV
Stok Durumu:
Yok
Teklif İsteyiniz Stoklara düşünce haber ver
Not
:
Aynı Gün Kargo 15’e kadar aynı gün kargo
Worldwide Shipment
Next Day Shipment
Kampanya

{{CMP.TITLE}}

{{CMP.DESCRIPTION}}

  • Ürün Özellikleri
  • İade ve Teslimat
  • Ödeme Seçenekleri
  • Yorumlar (0)
  • Beni Ara
  • Ek
  • R3 PLUS MCU Development Board

    Based On ATMEGA328P-AU

    Compatible with the Arduino official R3 board
     
    What's The Differences
    R3 PLUS OFFICIAL R3 REMARKS
    Operating voltage 5V/3.3V 5V Dual voltage level to support more shields
    Reset Lateral Vertical Lateral button is easier to use when connecting with shield
    Bootloader switch Yes None The board can be configured to run program immediately when power-up by the switch
    USB connector Micro USB USB Type B Micro connector is more commonly used, and shields won't be blocked anymore while connecting
    DC jack Low profile Normal height Shields won't be blocked anymore while connecting
    Power output header Yes None

    Providing 5V/3.3V power output OR common-grounding with other boards

    3.3V power output 800mA Max 150mA Max R3 PLUS features higher driving capability
    Oscillator Crystal oscillator Ceramic resonator Crystal oscillator is suit for applications where accurate clock reference is required
    ADC channel 8 6 CFG used as ADC6 by configuration, and ADC7 from the Reserved PIN
    Connecting with
    prototype breadboard    		 Supported Not supported Solder pads is provided for DIY interfaces to connecting with prototype breadboard
    USB driver Compatible with all main systems Doesn't compatible with WIN7/WIN8 Express Edition Driver will never failed to install thanks to the onboard FT232
    Firmware fixing Supported Not supported Firmware can be fixed by using the onboard FT232, no extra programmer is needed
    Connecting With Waveshare Shields

    Connecting With Motor Control Shield And IO Expansion Shield

    Connecting With Sorts Of Sensors

    What's On Board
    1. ATMEGA328P-AU
    2. AMS1117-3.3
      3.3V voltage regulator
    3. NCP1117ST50T3G
      5V voltage regulator
    4. FT232RL
      USB to UART convertor
    5. Arduino interface
      • compatible with standard Arduino interface with two additional analog inputs A6 (config the CFG), A7
      • solder pads provided, supports prototype breadboard
    6. ICSP interface
    7. MICRO USB connector
      for uploading program OR serial port debugging
    8. Power output header
      3.3V OR 5V, voltage level configured by the onboard power configuration switch, used as power output OR common-grounding with other boards
     
    1. FT232 pins
      for burning Bootloader into the microcontroller
    2. DC input
      7V ~ 12V
    3. Reset button
    4. Power indicator
    5. Serial port Rx/Tx indicator
    6. User LED
    7. 500mA fast auto-recovery fuse
    8. Power configuration
      for configuring the operating voltage
    9. Bootloader selection switch
      • turn ON: the board will reset when power-up OR other USB devices were detected connecting to the PC
      • turn OFF: the onboard program runs immediately when power-up, and the board will not reset when other USB devices were detected connecting to the PC
    Optional Development Kit

    Development Kit Is Also Available For Your Convenience

    Pinout Definition
    Outline Dimensions
    Resources & Services
    Wiki: R3_PLUS
Sepete Ekle
T-Soft E-Ticaret Sistemleriyle Hazırlanmıştır.